Configuring an IP block in a vRack
This guide will show you how to configure a block of public IP addresses for use with the vRack.
Last updated 26th July 2022
Objective
As well as private IP addressing, the vRack also allows you to route public IP traffic through your server's vRack port using a public IP address block.
This guide will show you how to configure a block of public IP addresses for use with the vRack.
Requirements
- A public block of IP addresses in your account, with a minimum of four addresses
- Your chosen private IP address range
- A vRack compatible server
- A vRack service activated in your account
- Access to the OVHcloud Control Panel
This feature might be unavailable or limited on servers of the Eco product line.
Please visit our comparison page for more information.
Instructions
For example purposes we'll be using an IP block of 46.105.135.96/28 and eth1 for the secondary network interface, which is dedicated to the vRack.
Add the IP block to the vRack
Once an IP block is added to the vRack, it is no longer attached to a physical server.
This setup allows you to configure IPs of the same block on multiple servers, provided that these servers are all in the same vRack as the IP block. The IP block must have at least 2 usable IPs or more for this to be possible.
In your OVHcloud Control Panel, go to the Bare Metal Cloud section and click on Network. Next, open the vRack menu.
Select your vRack from the list to display the list of eligible services. Click the IP block you wish to add to the vRack and click on the Add button.
Configure a usable IP address
For vRack purposes, the first, penultimate, and last addresses in any given IP block are always reserved for the network address, network gateway, and network broadcast respectively. This means that the first useable address is the second address in the block, as shown below:
46.105.135.96 Reserved: Network address
46.105.135.97 First usable IP
46.105.135.98
46.105.135.99
46.105.135.100
46.105.135.101
46.105.135.102
46.105.135.103
46.105.135.104
46.105.135.105
46.105.135.106
46.105.135.107
46.105.135.108
46.105.135.109 Last usable IP
46.105.135.110 Reserved: Network gateway
46.105.135.111 Reserved: Network broadcast
To configure the first usable IP address, we need to edit the network configuration file, as shown below. In this example, we need to use a subnet mask of 255.255.255.240.
The subnet mask we've used in our example is appropriate for our IP block. Your subnet mask may differ depending on the size of your block. When you purchase your IP block, you'll receive an email that will tell you which subnet mask to use.
/etc/network/interfaces
auto eth1
iface eth1 inet static
address 46.105.135.97
netmask 255.255.255.240
broadcast 46.105.135.111
Create a new IP routing table
First, we need to download and install iproute2, which is a package that will enable us to manually configure IP routing on the server.
Establish an SSH connection to your server and run the following command from the command line. This will download and install iproute2.
# apt-get install iproute2
Next, we need to create a new IP route for the vRack. We'll be adding a new traffic rule by amending the file, as shown below:
/etc/iproute2/rt_tables
#
# reserved values
#
255 local
254 main
253 default
0 unspec
#
# local
#
#1 inr.ruhep
1 vrack
Amend the network configuration file
For example purposes, the network configuration file we refer to is located in /etc/network/interfaces. The equivalent file on your server may be located somewhere else, depending on your operating system.
Finally, we need to amend the network configuration file to account for the new traffic rule and route the vRack traffic through the network gateway address of 46.105.135.110.
/etc/network/interfaces
auto eth1
iface eth1 inet static
address 46.105.135.97
netmask 255.255.255.240
broadcast 46.105.135.111
post-up ip route add 46.105.135.96/28 dev eth1 table vrack
post-up ip route add default via 46.105.135.110 dev eth1 table vrack
post-up ip rule add from 46.105.135.96/28 table vrack
post-up ip rule add to 46.105.135.96/28 table vrack
Now reboot your server to apply the changes.
Go further
Configuring the vRack on your dedicated servers
Creating multiple vLANs in a vRack
Configuring the vRack between the Public Cloud and a Dedicated Server
Join our community of users on https://community.ovh.com/en/.
Did you find this guide useful?
Please feel free to give any suggestions in order to improve this documentation.
Whether your feedback is about images, content, or structure, please share it, so that we can improve it together.
Your support requests will not be processed via this form. To do this, please use the "Create a ticket" form.
Thank you. Your feedback has been received.