Configurar a firewall distribuída NSX (EN)

Last updated on 1st December 2021


As does the NSX Edge Firewall, the distibuted firewall restricts or allows network traffic based on rules applied to network nodes or groups.

The distributed firewall optimizes traffic and bandwidth consumption by applying rules to packets before they are sent to the Edge firewall.

This guide explains how to create rules.



Interface access

In the vSphere interface menu, go to the Networking and Security dashboard.


On the left side, navigate to the Firewall section.


The distributed Firewall allows for:

  • General rules (layer 3 and up)
  • Ethernet rules (layer 2)
  • Partner Services rules (requires integration of third party products)



Before creating rules, it is important to understand how and when they will be applied.
The Distributed Firewall has three layers ot priority:

  • Types
  • Sections
  • Rules


The type of rules/sections is defined by the layer it will apply on.
Layer 2 rules will be applied before Layer 3 and up.
That means that Ethernet rules will have a higher priority than General ones.


Sections are rules folders that allow better segmentation and easier management.
Sections are applied from top to bottom.
That means that in the case of conflicting rules in different sections, the rule within the section with the highest priority will be applied.


Rules manage identified service(s) from specified source(s) to specified destination(s).
Rules are applied from top to bottom.
The first rule that matches the traffic overrides all the other rules below.
That means that in the case of conflicting rules within a section, the rule with the highest priority (lowest number) will be applied.


You can add rules and sections in any tabs of the firewall.
You can modify the rule/section order by selecting a rule/section and using the up and down arrows.


Firewall Rules

Click on + Add Rule.

The new rule shows with:

  • An activation slider
  • A selection box for specific actions (order change, deletion...)
  • Name
  • ID
  • Source
  • Destination
  • Service
  • Applied To
  • Action
  • Log slider
  • Advanced settings


By default, rules have Any as source and destination, meaning it encompasses all traffic. To avoid security issues, it is best practices to avoid broad targets.


Name the rule by clicking the Name field. The ID field will be automatically populated.


The source field defines the origin of the traffic.

Hover over the field and click on the pencil icon. You can add objects and/or IP addresses as needed.

If "Negate Source" is turned on, the rule is applied to all sources except for the sources selected.

Click Save when ready.




The destination field defines the target of the traffic.

Hover over the field and click on the pencil icon. You have the same choices for destination as you had for source.

If "Negate Source" is turned on, the rule is applied to all destinations except for the destinations selected.

Click Save when ready.




The service field defines the type of traffic aimed at.

Hover over the field and click on the pencil icon. You have the choice between using existing services and groups or adding raw ports/protocols.

Clicking on an existing service or group will show you a description of the ports and protocols involved.

Click Save when ready.




Applied To

The applied to field defines the scope of the rule.

Hover over the field and click on the pencil icon.
By default, the rule is set to apply to all clusters on which Distributed Firewall is installed, which means it will apply to all VMs.
You can add all Edge gateways or specific objects available in the list.

Click Save when ready.



The action field defines how to handle the traffic.

You have three possible options to choose from:

  • Allow: The traffic will go through.
  • Block: The traffic will be blocked with no further communication.
  • Reject: The traffic will be blocked and a "port unreachable" message will be sent to the source.



The log slider allows you to keep a journal of events on the rule.

Advanced Settings

Aside from a comments section and a statistics section, the advanced settings section allows you to define if the target traffic is inbound, outbound or both and if you want to target IPv4, IPv6 or both.

Click Save when ready.


Publishing rules

No creation/modification of a rule/section will be registered until you click the Publish button.


Go further

Join our community of users on

Esta documentação foi-lhe útil?

Não hesite em propor-nos sugestões de melhoria para fazer evoluir este manual.

Imagens, conteúdo, estrutura... Não hesite em dizer-nos porquê para evoluirmos em conjunto!

Os seus pedidos de assistência não serão tratados através deste formulário. Para isso, utilize o formulário "Criar um ticket" .

Obrigado. A sua mensagem foi recebida com sucesso.

Estes manuais também podem ser úteis...

OVHcloud Community

Aceda ao seu espaço comunitário. Coloque as suas questões, procure informações e interaja com outros membros do OVHcloud Community.

Discuss with the OVHcloud community

Em conformidade com a alteração à Diretiva 2006/112/CE, os preços com IVA podem variar de acordo com o país de residência do cliente
(por defeito, os preços com IVA apresentados incluem o IVA português em vigor).